• OPERATING MODES
      
    • 802.11a/b/g/n Aruba Instant AP
    • 
    • 802.11a/b/g/n Mobility Controller-managed AP
    • 
    • Air monitor (AM) for wireless IDS, rogue detection and containment
    • 
    • Spectrum analyzer
    • 
    • Secure enterprise mesh
    • 
    • Remote AP (RAP) when used with a Mobility Controller
    WIRELESS RADIO SPECIFICATIONS
      
    • AP type: Indoor, dual radio, 5-GHz and 2.4-GHz 802.11n 2x2:2
    • 
    • Software-configurable dual radio supports 5-GHz (Radio 0) and 2.4-GHz (Radio 1)
    • 
    • 2x2 MIMO with two spatial streams and up to 300 Mbps wireless data rate
    • 
    • Supported frequency bands (country-specific restrictions apply):
        
      • 2.4000 to 2.4835 GHz
      • 
      • 5.150 to 5.250 GHz
      • 
      • 5.250 to 5.350 GHz
      • 
      • 5.470 to 5.725 GHz
      • 
      • 5.725 to 5.850 GHz
    • 
    • Support for up to 256 associated client devices per radio, and up to 16 BSSIDs per radio
    • 
    • Available channels: Dependent on configured regulatory domain
    • 
    • Dynamic frequency selection (DFS) optimizes the use of available RF spectrum
    • 
    • Supported radio technologies:
        
      • 802.11b: Direct-sequence spread-spectrum (DSSS)
      • 
      • 802.11a/g/n: Orthogonal frequency-division multiplexing (OFDM)
    • 
    • Supported modulation types:
        
      • 802.11b: BPSK, QPSK, CCK
      • 
      • 802.11a/g/n: BPSK, QPSK, 16-QAM, 64-QAM
    • 
    • Transmit power: Configurable in increments of 0.5 dBm 
    • Maximum (aggregate, conducted total) transmit power (limited by local regulatory requirements):
      • 
      • 2.4-GHz band: +21 dBm (18 dBm per chain)
      • 
      • 5-GHz band: +21 dBm (18 dBm per chain)
      
    • Advanced Cellular Coexistence (ACC) minimizes interference from LTE cellular networks
    • 
    • Maximum ratio combining (MRC) for improved receiver performance
    • 
    • Cyclic delay/shift diversity (CDD/CSD) for improved downlink RF performance
    • 
    • Short guard interval for 20-MHz and 40-MHz channels
    • 
    • Space-time block coding (STBC) for increased range and improved reception
    • 
    • Low-density parity check (LDPC) for high-efficiency error correction and increased throughput
    • 
    • Supported data rates (Mbps):
        
      • 802.11b: 1, 2, 5.5, 11
      • 
      • 802.11a/g: 6, 9, 12, 18, 24, 36, 48, 54
      • 
      • 802.11n: 6.5 to 300 (MCS0 to MCS15)
    • 
    • 802.11n high-throughput (HT) support: HT 20/40
    • 
    • 802.11n packet aggregation: A-MPDU, A-MSDU
    • 
    POWER
      
    • Maximum power consumption: 9.5W (POE) or 8W (DC)
    • 
    • Power sources sold separately
    • 
    • Direct DC source: 12 Vdc nominal, +/- 5%
    • 
    • Power over Ethernet (PoE): 48 Vdc (nominal) 802.3af or 802.3at-compliant source
    • 
    ANTENNAS
      
    • Two integrated dual-band downtilt omni-directional antennas for 2x2 MIMO with maximum antenna gain of 4.0 dBi in 2.4 GHz and 4.5 dBi in 5 GHz. Built-in antennas are optimized for horizontal ceiling mounted orientation of the AP. The downtilt angle for maximum gain is approximately 30 degrees.
    • 
    OTHER INTERFACES
      
    • 10/100/1000BASE-T Ethernet network interface (RJ-45)
        
      • Auto-sensing link speed and MDI/MDX
      • 
      • 802.3az Energy Efficient Ethernet (EEE)
      • 
      • PoE-PD: 48 Vdc 802.3af PoE or 802.3at PoE+
    • 
    • DC power interface, accepts 1.7/4.0-mm center-positive circular plug with 9.5-mm length
    • 
    • Serial console interface (proprietary; optional adapter cable available)
    • 
    • Visual indicators (LEDs):
        
      • Power/system status
      • 
      • Ethernet link status (ENET)
      • 
      • Radio status (2x; RAD0, RAD1)
    • 
    • Kensington security slot
    • 
    • Reset button
    • 
  • 
    MOUNTING
      
    • Included with AP:
        
      • Mounting brackets (2) for attaching to 9/16-inch or 15/16-inch T-bar drop-tile ceiling
    • 
    • Spare mounting kit:
        
      • AP-220-MNT-C1: Aruba AP mount kit contains two ceiling-grid rail adapters for flat rails
    • 
    • Optional mounting kits:
        
      • AP-220-MNT-C2: Aruba AP mount kit contains two ceiling-grid rail adapters for Interlude and Silhouette style rails
      • 
      • AP-220-MNT-W1: Aruba AP mount kit contains one flat-surface wall/ceiling mount bracket
      • 
      • AP-200-MNT-W3: Aruba AP mount kit contains one flat-surface wall/ceiling secure mount cradle
    • 
    MECHANICAL
      
    • Dimensions/weight (unit, excluding mount accessories):
        
      • 150 mm (W) x 150 mm (D) x 41.5 mm (H)
      • 
      • 5.9” (W) x 5.9” (D) x 1.63” (H)
      • 
      • 300 g (0.66 lbs)
    • 
    • Dimensions/weight (shipping):
        
      • 192 mm (W) x 178 mm (D) x 68 mm (H)
      • 
      • 7.6” (W) x 7.0” (D) x 2.68” (H)
      • 
      • 500 g (1.10 lbs)
    • 
    ENVIRONMENTAL
      
    • Operating:
        
      • Temperature: 0° C to +40° C (+32° F to +104° F)
      • 
      • Humidity: 5% to 93% non-condensing
      
    • 
    • Storage and transportation temperature range:
        
      • Temperature: -40° C to +70° C (-40° F to +158° F)
      
    • 
    REGULATORY
      
    • FCC/Industry of Canada
    • 
    • CE Marked
    • 
    • R&TTE Directive 1995/5/EC
    • 
    • Low Voltage Directive 72/23/EEC
    • 
    • EN 300 328
    • 
    • EN 301 489
    • 
    • EN 301 893
    • 
    • UL/IEC/EN 60950
    • 
    • EN 60601-1-1 and EN 60601-1-2
    • 
    • For more country-specific regulatory information and approvals, please see your Aruba representative.
    • 
    REGULATORY MODEL NUMBERS
      
    • AP-103 and IAP-103: APIN0103
    • 
    CERTIFICATIONS
      
    • CB Scheme Safety, cTUVus
    • 
    • UL2043 plenum rating
    • 
    • Wi-Fi Alliance (WFA) certified 802.11a/b/g/n
    • 
    WARRANTY
      
    • Limited lifetime warranty
    • 
    MINIMUM SOFTWARE VERSIONS
      
    • ArubaOS 6.4.0.0
    • 
    • Aruba InstantOS 4.1.0.0
    •